Datamax-oneil Workstation series User Guide Instrukcja Użytkownika

1 | SafetyWorkstation Series User’s Guide 2The printhead heats during printing. Do not touch.Caution: Serious damage and bodily injury can result

3 Workstation Series User’s Guide2OverviewWorkstation Series Overvieww1110 Product TourThe following illustrations show some of the features and avail

2 | OverviewWorkstation Series User’s Guide 4Figure: 2 - 2 Rear View - w1110 1. Power Switch2. DC Power Inlet3. Reset Button4. USB 2.0 Port5. Ethe

Overview | 25 Workstation Series User’s GuideFigure: 2 - 3 Media Area .1. Printhead2. Upper Top-of-Form Sensor3. Cover Latch4. Left Media Support

2 | OverviewWorkstation Series User’s Guide 6OptionsFigure: 2 - 4 Peel and Present Figure: 2 - 5 Serial Interface 121. Peel Bar2. Present Sensor1

Overview | 27 Workstation Series User’s GuideStandard FeaturesThe thermal printer has the following standard features:Table 1: Standard FeaturesF

2 | OverviewWorkstation Series User’s Guide 8OptionsThe following options are available:• Peel and Present• Serial Interface• Non-US Power CordsUn

Overview | 29 Workstation Series User’s GuideSpecificationsPrint CharacteristicsTable 2: Print Characteristics*Media wound out.Dimensions and Wei

2 | OverviewWorkstation Series User’s Guide 10Configuration UtilityTable 6: Configuration Utility Minimum System RequirementsSupported Operating S

11 Workstation Series User’s Guide3 Connections and SetupConnectionsPowerTo connect the printer to a viable power source, please follow the steps belo

3 | Connections and SetupWorkstation Series User’s Guide 12Media LoadingThe w1110 printer supports either a 1” core or a 1.5” core paper roll. The

Connections and Setup | 313 Workstation Series User’s GuideNote: Ensure the core adapters have snapped into place.3. Slide the media support brac

3 | Connections and SetupWorkstation Series User’s Guide 145. Route the paper under the support bracket guides.Figure: 3 - 3 Support Bracket Guide

Connections and Setup | 315 Workstation Series User’s Guide1. Open the peel and present sub-assembly.a. Rotate the peel and present sub-assembly

3 | Connections and SetupWorkstation Series User’s Guide 16Note: Be sure there are no labels attached to the backing that is routed behind the pee

Connections and Setup | 317 Workstation Series User’s GuideControl PanelThe control panel consists of the two (2) main buttons on the printer cov

3 | Connections and SetupWorkstation Series User’s Guide 18ButtonsThe operation of the buttons consists of long or short presses depending on the

Connections and Setup | 319 Workstation Series User’s GuideSensor CalibrationSensor calibration is set during the manufacturing process and shoul

3 | Connections and SetupWorkstation Series User’s Guide 20Print Driver InstallationOverviewThis installation should be executed only on a compute

Connections and Setup | 321 Workstation Series User’s Guide6. Check the “Install printer drivers” radio button then click ‘Next’ and follow the o

Workstation Series User’s GuideCopyright Information CG Triumvirate is a trademark of Agfa Corporation.CG Times based upon Times New Roman under licen

3 | Connections and SetupWorkstation Series User’s Guide 22

53 Workstation Series User’s Guide4 Operation Printer ModesThe w1110 features three (3) modes:• Tear Mode• Present Sensor Mode• Pause ModeThe modes ar

4 | OperationWorkstation Series User’s Guide 54To continue the print job, select the Stop/Resume button. The print job can be canceled by selectin

Operation | 455 Workstation Series User’s GuideTo print the System Report, select the Reset button and the Feed/Cancel (right) button with a shor

4 | OperationWorkstation Series User’s Guide 56• Auto Option Detect• Auto Present Distance• Auto Speed AdjustAdjustment Settings• Present Distance

57 Workstation Series User’s Guide5 Cleaning and MaintenanceOverviewTo maintain good print quality and increase printhead life, proper cleaning should

5 | Cleaning and MaintenanceWorkstation Series User’s Guide 58

59 Workstation Series User’s Guide6 TroubleshootingLED IndicatorsThe printer LEDs are also used to indicate errors and warnings. Refer to the followin

6 | TroubleshootingWorkstation Series User’s Guide 60Note: To clear errors, open the printer cover fully and then close and latch it.WarningsTroub

Troubleshooting | 661 Workstation Series User’s GuideTroubleshooting Print QualityTools• Datamax-O’Neil approved media• Magnifying lens• Barcode

Workstation Series User’s Guide

6 | TroubleshootingWorkstation Series User’s Guide 622. Load the media according to the instructions in the Setup section.Note: Verify that the pa

63 Workstation Series User’s Guide7 Appendix ASymbol SetsThe following Symbol Sets are available:Table 1: Symbol SetsNumber Symbol Sets0PC-81Roman-82R

7 | Appendix AWorkstation Series User’s Guide 64FontsThe following Fonts are supported:Table 2: Fonts 28 ISO-629 ISO-1130 ISO-1531 ISO-1732 ISO-21

Appendix A | 765 Workstation Series User’s GuideCG Omega <ESC>(<symset><ESC>(s1p<ptsize>v0s0b4113TCG Omega Italic <ESC

7 | Appendix AWorkstation Series User’s Guide 66BarcodesThe following barcodes are supported:Table 3: Barcodes Vera Regular Mono <ESC>(<s

Appendix A | 767 Workstation Series User’s Guide1091 MSI Plessey Mod 10 1-55 0-91100 Code 93 1-107 ASCII 0x20-0x7F1110 HIBC Code 93 1-36 0-9, A-Z

Agency ComplianceThis product complies to the following:CFR 47 Part 15, Class A Digital DeviceThis device complies with Part 15 of the FCC Rules. Ope

Workstation Series User’s GuideTable of Contents Agency Compliance ...

Table of ContentsWorkstation Series User’s GuideImportant Notes: ......

1 Workstation Series User’s Guide1 Safety Warnings and CautionsThe following Warnings and Cautions are used throughout this manual:Warning: Warnings a