Datamax-oneil Class Series II Programmer’s Manual Instrukcja Użytkownika Strona 272
- Strona / 334
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Appendix J – General Purpose Input Output Port Applications
258 Class Series 2 Programmer’s Manual
Applicator Interface Card (Type 1) Jumper Locations
The GPIO Port allows printer integration. Functions can be configured using the menu
system or via <STX>Kc commands. All configuration settings are saved in non-volatile
memory. Jumper settings are critical:
• Jumper settings allow internal or external power distribution to the applicator circuitry.
• Jumper settings allow + 5 or +24 VDC output signal levels.
Failure to configure the card for the device(s) you are connecting may result in damage
to the printer and/or the applicator.
The table below details the GPIO Port functions, and configurable settings:
- Class Series II 1
- Contents 7
- Overview 15
- General Conventions 17
- Special Instructions 18
- Typical Data Flow Sequence 18
- Configuration Commands 19
- ) commands can be changed at 21
- Alternate Control Code Modes 24
- Immediate Command Functions 26
- SOH B Toggle Pause 27
- SOH C Stop/Cancel 28
- SOH D SOH Shutdown 28
- SOH F Send Status Byte 29
- STX e Select Edge Sensor 34
- STX F Form Feed 34
- STX I Input Image Data 35
- STX k Test RS-232 Port 37
- STX o Cycle Cutter 40
- STX P Set Hex Dump Mode 40
- STX p Controlled Pause 40
- STX Q Clear All Modules 41
- STX q Clear Module 41
- STX R Ribbon Saver Control 41
- STX S Set Feed Speed 42
- STX T Print Quality Label 42
- STX X Set Default Module 47
- STX z Pack Module 50
- STX Kb Backfeed Time Delay 55
- STX KC Get Configuration 56
- STX Kc Configuration Set 57
- (if available) 58
- (MP Comapct4 Mark II only) 63
- (for firmware versions 67
- 14.00 and later) 67
- 13.99 and earlier) 67
- (continued) 74
- STX KE Character Encoding 117
- STX KI GPIO Input 122
- STX Kn NIC Reset 122
- STX KO GPIO Output 123
- STX Kp Module Protection 124
- Introduction 139
- A Set Format Attribute 140
- C Set Column Offset Amount 141
- B Bar Code Magnification 141
- H Enter Heat Setting 145
- J Justification 145
- M Select Mirror Mode 146
- P Set Print Speed 147
- R Set Row Offset Amount 148
- S Set Feed Speed 150
- Embedding 155
- ^ Set Count by Amount 156
- STX D Print adjusted date 157
- STX T Print Time and Date 158
- )s###W Font Descriptor 162
- *c###E Character Code 162
- Generating Label Formats 163
- Generating Records 164
- The Structure of a Record 164
- Record Structure Types 168
- 176
- Figure 1 178
- Figure 2 178
- Figure 3 179
- Appendix A 181
- ASCII Control Chart 181
- 10K OHM 1/4 WATT 183
- Appendix B – Sample Programs 184
- Appendix C 193
- Appendix C – Available Fonts 196
- Appendix D 199
- Reset Codes 199
- Appendix D – Reset Codes 200
- Single Byte Symbol Sets 201
- Appendix F 213
- Bar Code Summary Data 213
- Appendix G 219
- Bar Code Details 219
- Barcode I 224
- Barcode S 228
- Barcode T 228
- Barcode U 231
- Barcode z 232
- Barcode Z 233
- Barcode W1c 235
- Barcode W1C 236
- Barcode W1D 240
- Barcode W1f 245
- Barcode W1F 245
- Barcode W1G 246
- Barcode W1I 248
- Barcode W1J 249
- Barcode W1k 251
- Barcode W1L 253
- Barcode W1M 255
- Barcode W1m 255
- Barcode W1N 255
- (IMB) 256
- 34 567890 123 4567 258
- Barcode W1t 259
- Barcode W1Y 260
- Barcode W1Z 262
- Appendix H 265
- Appendix J 271
- • Pins 1 – 2 = +5VDC; 277
- • Pins 2 – 3 = +24VDC; or 277
- • None = A common external 277
- Signal Out 280
- Signal In 280
- I-Class GPIO 281
- M-Class II GPIO 282
- Maximum Format Fields 285
- Appendix L 289
- Speed Ranges 289
- Appendix M 291
- Commands by Function 291
- Appendix N 293
- Image Loading 293
- Appendix N – Image Loading 294
- Figure N-2: Sample Label 294
- Appendix O 295
- Programming Examples 297
- ILPC - Kanji 298
- ILPC - Chinese 302
- ILPC - Korean 305
- Appendix Q 307
- Plug and Play IDs 307
- Appendix R 309
- Line Mode 309
- Appendix R – Line Mode 310
- Appendix S 313
- RFID Overview 313
- Label Formatting Mode 314
- Appendix S – RFID Overview 316
- Field Valid Inputs Meaning 317
- GEN2 Kill/Access Passwords 318
- GEN2 Lock States 318
- Appendix T 319
- WiFi Region Country Codes 319
- Appendix U 325
- Graphics Display Icon Key 325
- Appendix V 329
- Glossary 331
Powiązane produkty i podręczniki dla Drukarki Datamax-oneil Class Series II Programmer’s Manual
(58 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji